鲜切加工设备的使用周期到达一定时间范围内，是需要进行大幅度的维护保养的，当然为了不那么麻烦，我们在平常就可以通过定期的维护来让该设备不受损，下面小编就维护保养以及注意事项来讲讲内容吧。
When the service life of the fresh cutting processing equipment reaches a certain range of time, it needs a large amount of maintenance. Of course, in order to avoid such trouble, we can usually protect the equipment from damage through regular maintenance. Now let's talk about the maintenance and precautions.
维护保养
Maintenance
1、对于链条的调整：该调整是在马达停止之后进行的，在两链轮的中间以手指来压链条，压缩量一般为4到9毫米之间是标准值，当一旦超过标准值得时候就调整惰轮规定紧度。
1. Adjustment of the chain: the adjustment is carried out after the motor stops. Press the chain between the two sprockets with a finger. The compression amount is generally 4 to 9 mm, which is the standard value. Once the standard value is exceeded, adjust the idler gear to the specified tightness.
2、对于无段变速的更换：无段变速齿轮箱机油之点检加油及更换，是要停止马达，严禁烟火得情况下拆掉检油塞，油刚流出为适当之量，不足时补充之。
2. For the replacement of the stepless speed change: For the spot check and oil filling and replacement of the stepless speed change gear box oil, the first step is to stop the motor. It is strictly prohibited to remove the oil inspection plug under the condition of fireworks. The amount of oil just flowing out is appropriate, and it should be supplemented when it is insufficient.
3、长期不使用时的保存：当我们要进行长时间的保存而不使用时我们就可以把各部分的泥土等的物体进行冲洗擦拭干净，各个回转部以及皮带和链条等的附着的杂物都要完全的而且各回转部及磨擦主动部，充分注油以防止生锈现象的出现。
3. Storage when not in use for a long time: When we want to keep it for a long time without using it, we can wash and wipe the dirt and other objects in all parts. The sundries attached to all rotating parts, belts and chains should be completely removed. All rotating parts and friction driving parts should be fully oiled to prevent rust.
注意事项
matters needing attention
一、操作人员使用前应检查管路系统有无漏气漏水的情况，如果有应及时解决，并建立设备操作维护日志。
1、 Operators shall check whether there is air or water leakage in the pipeline system before use. If there is, it shall be solved in time, and equipment operation and maintenance logs shall be established.
二、设备运行前应试运行，让设备先空运转2-3分钟，检查传动系统和运输带的运动是否平稳。
2、 Test run the equipment before operation, let the equipment run for 2-3 minutes without load, and check whether the movement of the transmission system and the conveyor belt is stable.
三、开启浮油排除装置，因此时水泵尚开启，水面平静，排油效果好，待浮油基本排除后停止除油，排油污多利用休息时间进行。
3、 Start the oil slick removal device, so the water pump is still on, the water surface is calm, and the oil drainage effect is good. Stop the oil removal after the oil slick is basically removed, and the oil stain is mostly discharged during the rest time.
四、将待处理的蔬菜等物料要整齐地放在运输带上，不能压在滚轮上，操作时一定要注意。
4、 The vegetables and other materials to be treated shall be placed on the transport belt orderly, and shall not be pressed on the roller. Pay attention to the operation.
五、操作人员要对我们的蔬菜清洗流水线做好维护。
5、 Operators should maintain our vegetable cleaning line.
The maintenance and other precautions of the fresh cutting processing equipment are explained here. If you have any questions or needs, you can come to our website at any time https://www.sfxjxbj.com consulting service
