沙拉机如果操作不当或是保养不合理，不仅沙拉机的使用寿命达不到预期的时长，同时还严重影响沙拉的口感味道。那么，沙拉加工设备在使用操作时都有哪些注意事项呢？

If the salad machine is operated improperly or the maintenance is unreasonable, not only the service life of the salad machine can not reach the expected time, but also seriously affect the taste of the salad. So, what are the precautions for the use and operation of salad processing equipment?

使用沙拉加工设备时，需要空转机器，检查是否有异常噪音。如果空转正常，可以使用。在使用沙拉加工设备时，必须空机运行，检查是否有异常响声。如果空闲运行正常，则可以使用。开机前检查滚筒和沙拉机刀是否有杂物，清洗干净后再开机。擦拭沙拉加工设备时应切断电源；

When using salad processing equipment, it is necessary to idle the machine and check whether there is abnormal noise. If idling is normal, it can be used. When using salad processing equipment, the machine must run empty to check whether there is abnormal noise. It can be used if it is idle. Before starting up, check whether there are sundries in the drum and salad knife, and start up after cleaning. Cut off the power supply when wiping the salad processing equipment;

沙拉加工设备运行时，随时注意水箱内水位的蒸发，防止水量不足造成电暖器干烧损坏；生产前水温达到90-100度时，可暂时关闭电加热器保持水温以减少用电，生产前准备完成后可开启电热管；每天使用后，必须打开水闸，将水箱内的水放掉，以防结冰。上班前加冷水或热水，不易加水过多立即覆盖主轴上方2-3厘米；

When the salad processing equipment is running, pay attention to the evaporation of the water level in the water tank at any time to prevent the dry burning damage of the electric heater caused by insufficient water; When the water temperature reaches 90-100 degrees before production, the electric heater can be turned off temporarily to maintain the water temperature to reduce power consumption. After the preparation before production, the electric heating pipe can be turned on; After use every day, the sluice must be opened to drain the water in the water tank to prevent freezing. Add cold water or hot water before work. It is not easy to add too much water. Immediately cover 2-3cm above the spindle;

沙拉加工设备每班换班前，应在三通、筛底、轴承套内侧和丝杠轴上涂抹少量食用油，然后依次安装，机器应打开。每班后，应使用松线机。头部各螺纹锁紧，防止老化后锁紧，无法拆卸；沙拉加工设备工作中发现异响时，应及时停机检查；

Before each shift of salad processing equipment, a small amount of edible oil shall be applied on the tee, screen bottom, inner side of bearing sleeve and lead screw shaft, and then installed in turn. The machine shall be turned on. After each shift, the thread loosening machine shall be used. Each thread of the head is locked to prevent it from being locked after aging and cannot be disassembled; In case of abnormal noise during the operation of salad processing equipment, it shall be shut down in time for inspection;

操作沙拉加工设备时，应注意，防止发生不事故；沙拉机的安装和使用应按照用电规定谨慎操作；轴承工作200-300小时后，需要拆开润滑脂；使用后，关闭并切断电源，清洗机身上的掺假色拉。

Pay attention to safety when operating salad processing equipment to prevent unsafe accidents; The salad machine shall be installed and used carefully in accordance with the provisions on safe power consumption; After the bearing works for 200-300 hours, the grease needs to be disassembled; After use, turn off and cut off the power supply and clean the adulterated salad on the body.

以上所讲内容大家有了解过吗？如何尽量避免操作失误，降低沙拉加工设备故障率，更好的延长设备使用寿命，更多内容的了解就来网站www.sfxjxbj.com关注吧！

Have you understood the above contents? How to avoid operation errors as much as possible, reduce the failure rate of salad processing equipment and better prolong the service life of the equipment? For more information, please visit www.sfxjxbj.com Com follow!